Maşini rindeluit 4 feţe
- Mașină de turnat profesional pentru lemn marca Casolin Model 6-230 Anul 1998 ( CE ) Masa de pre-rindea 2000 mm lungime Latime de lucru 230 mm1998
- Mașină de turnat Weinig mod. P23 ce 5 catarge + universal Anul 1996 Stare folosita
- Mașină de turnat concepută pentru a răspunde nevoilor industriilor mici și mijlocii care necesită un grad ridicat de flexibilitate a producției. Arbore orizontal inferior Arbore vertical...2000
- Lățime de lucru mm: 330 Înălțimea planificării mm: 120 Lungimea mesei introduse mm: 1800 Frecvență m / min: 6-36 (INVERTER) Viteza de rotatie max rpm: 6500 Numărul de arbori: 6 Configu...2012
- DATE TEHNICE: Lățime de lucru mm: 230 Înălțimea de rindeluire mm: 120 Lungimea mesei de alimentare mm: 3500 Numărul de fusuri: 6 Configurarea axului: 1 B: 5,5 KW 2 R: 7,5 KW 3 L:...2004
- Vand masina de taiat si ghins dublu FRIULMAC IDRAMAT, An 2007. Latime de lucru pana la 2500 mm Configurație partea stângă/remediere: 1 + 1 buc. agregate fierăstrău de tăiat / 3,0 + 3,0...42 000,00 €2007
- turnător LEADERMAC 4 arbori mod. LMC-428C an 2007 CE - turnatorie stanga motorizata - reglaje din panoul de comanda - 4 motoare independente de 15 CP - masa de 23 cm2007
- Producator FAMOT Jvxnva Model/tip mașină TNFJ An fabricatie 1966 COLECȚIA DEȚINEA MAȘINA DUPA O RENOVARE COMPLETĂ FRAZĂ FAMOT DUPĂ O RENOVARE MAJORĂ INSTALARE ELECTRICĂ NOUĂ INSTALARE...2000
- Cod: (006247) Max. înălțime prelucrabilă: 120 mm Lățimea maximă prelucrabilă: 230 mm Masa culisanta captusita: da Max. viteza de avans: 25 m/min Număr arbori operator: 5
- Holzmann VS20 - Mașină de turnat cu 4 arbori CE folosit Mașină de turnat Holz Mann VS20 cu 4 arbori Masina functioneaza in stare excelenta, in conformitate cu reglementarile CE
- Rindea Unimat 23 pentru lemn umed WEINIG Unimat 23 Rindeau umed pentru lemn cu 7 capete. sistem de cap jos orizontal, dreapta verticală, stânga verticală, sus orizontală, jos orizontală,...1999
- Modeler folosit 5 arbori: - Latime piesa finita cu scule ø125 20 ÷ 230 mm - Înălțimea piesei finisate cu scule de ø125 și ø100 pe universal 7-120 mm - Putere motor standard pe arbori vert...2000
- Mașină de turnat WEINIG model UNIMAT 17A cu 8 axe: -dimensiuni utile de lucru 170x120mm -acționare cardan și presiune pneumatică -viteza de alimentare variabila de la 6,3 la 36...1985
- Mașină de turnat WEINIG model UNIMAT 17N cu 8 axe: -dimensiuni utile de lucru 170x120mm -acționare cardan și presiune pneumatică -viteza de alimentare variabila -rola de ali...1981
- Mașină de turnat SCM SUPERSET NT Primul arbore inferior al 2-lea arbore RH Al 3-lea arbore SX al 4-lea ax superior al 5-lea arbore superior al 6-lea arbore inferior Greutate neta...2014
- PRODUCT CODE: PG1350 - 1957 SCM Compact NTE Professional Woodworking Moulding Machine (Year 2012) – 4 Spindles The SCM Compact NTE is a moulding machine (4-sided planer) designed for t...2012
- Cod: (008403) Max. machinable height: 160 mm Maximum machinable width: 250 mm Max. forward feed speed: 24 m/min Operator shafts number: 5
- Second-hand 4 spindles moulder SCM mod. COMPACT 23K Composition - 1st bottom horizontal spindle - 2nd vertical spindle right - 3rd vertical spindle left - 4th horizontal top - Working...2000
- Automatic spindle moulder CASADEI mod. MATRIX 5 (4+UNIVERSAL) - CE rules - Year 2005 - Composition: * horizontal bottom * vertical right * vertical left * horizontal top - Universal...2005
- Moulder (4-side planer) LMG Leadermac Smart MA 423 mod. LMC-423S - 4 spindles - used working width mm. 15-230 working thickness mm. 10-150 min. lenght of work piece mm. 200 spindle...2007
- Year of manufacture 2022 Working width 350 mm Planing height 160 mm Number of spindles 4 Bottom spindles 1 Right spindles 1 Spindles left 1 Spindles top 1 Spindle configuration b-r-l-t Spind...2022
- Year of manufacture 2017 Working width 230 mm Planing height 160 mm Number of spindles 5 Bottom spindles 2 Right spindles 1 Spindles left 1 Spindles top 1 Spindle configuration b-r-l-t-b Spi...2017
- Automatic 5-spindle moulding machine SCM COMPACT 23 - CE Standard for joinery, profiles, frames, wooden doors and windows, furniture, timber joinery, sawmills and various...
- Griggio moulder, CE compliant. Width 230 mm - 4 spindles
- Second-hand 6 spindles moulder SCM mod. SUPERSET NTPL - CE rules - 1. Horizontal bottom 11 kw - 2. Vertical right 7.5 kw - 3. Vertical left 7.5 kw - 4. Horizontal top 11 kw - 5. Horizon...2012
- Weinig Unimac 22 E moulder complete with: Lubrication on the table 1. Lower spindle - 2. Right spindle - 3. Left spindle - 4. Right spindle - 5. Upper spindle - 6. Lower spindle - 7. Univ...
- Cod: (007243) Max. machinable height: 120 mm Maximum machinable width: 230 mm Max. forward feed speed: 12 m/min Operator shafts number: 4
- Year of manufacture 2014 Working width 230 mm Planing height 160 mm Number of spindles 5 Bottom spindles 2 Right spindles 1 Spindles left 1 Spindles top 1 Spindle configuration b-r-l-t-b Spi...2014
- Infeed pre-planer: 1970 mm Working width: 250 mm Working height: 150 mm Shafts: Ø 40 mm Number of shafts: 5 Cardan shaft drive (2.2 kW) RPM: 6000 Installed power: 22 kW Voltage: 380...1996
- Weinig 8+1 spindle moulder MODEL UNIMAT 23 E CE-COMPLIANT - Composition: Heads 1 lower 7.5 kW 2 right 11 kW 3 left 11 kW 4 right 11 kW 5 upper 11 kW 6 lower 11 kW 7 up to 11 kW...2000
- SCM Sintex NT moulder - E standards Working width 23–180 mm Working height 6–105 mm Number of spindles: 42006
- 5 spindles moulder WEINIG mod. UNIMAT 500 - Composition: 1st lower horizontal spindle 2nd right vert. 3rd left vert. 4th upper horizontal spindle 5th lower horizontal spindle - Comple...2002
- PRODUCT CODE: PI1341 - 1946 SCM Superset 23 PLUS (1996) – Through-feed Moulder / Planer-Moulder (7 Spindles) The SCM Superset 23 PLUS is a professional through-feed moulder for the com...1996
- R51-03-1889 Weinig 7-Spindle Professional Woodworking Moulding Machine The Weinig 7-spindle moulding machine with cardan shaft is a top-quality machine for professional woodworking. De...
- Infeed pre-planer length: 1970 mm Working width: 230 mm Working height: 120 mm Shafts: Ø 40 mm Number of shafts: 6 Cardan shaft drive Installed power: 38 kW Voltage: 380 V SHAFT CO...2005
- Used Weinig Hydromat 22 A Moulder, C477 Infeed pre-planer length: 1980 mm Working width: 220 mm Working height: 120 mm Spindles: Ø 40 mm Number of spindles: 8 Cardan shaft drive (7.5 k...
- Working width: 450 mm Working height: 120 mm Shafts: Ø 40 mm Planers: Ø 50 mm Counter-supported lower planer spindles Number of spindles: 5 Installed power: 56 kW SPINDLE CONFIGURAT...1995
- Infeed pre-planer length: 1970 mm Working width: 230 mm Working height: 110 mm Shafts: Ø 40 mm Number of shafts: 4 Cardan shaft Installed power: 16 kW Voltage: 380 V COMPOSITION:...
- Length of infeed pre-planer: 1900 mm Working width: 190 mm Working height: 120 mm Shafts: Ø 35 mm Number of shafts: 6 Chain drive COMPOSITION: LOWER (3 kW) RH (2.2 kW) UPPER (4...
- Infeed pre-planer length: 1970 mm Working width: 230 mm Working height: 120 mm Shafts: Ø 40 mm Number of shafts: 5 Direct drive / PTO drive (0.25 kW x 3 motors) RPM: 6000 rpm Installe...2007
- Pre-planer entry length: 1970 mm Working width: 230 mm Working height: 120 mm Shafts: Ø 40 mm Number of shafts: 6 Cardan shaft drive (4 kW) RPM: 6000 RPM Installed power: 43 kW Equip...
- Infeed pre-planer length: 2500 mm Working width: 240 mm Working height: 130 mm Shafts: Ø 40 mm Number of shafts: 4 Cardan shaft drive (2.9 kW) Installed power: 24 kW Voltage: 380 V...2007
- Automatic 8+1 spindle moulder WEINIG mod. UNIMAT 17A Spindle configuration: 1. Bottom horizontal 2. Right vertical 3. Left vertical 4. Right vertical 5. Top horizontal 6. Bottom horiz...
- Automatic 8-spindle moulder WEINIG mod. UNIMAT 17A Spindle configuration: 1. Bottom horizontal 2. Right vertical 3. Left vertical 4. Right vertical 5. Top horizontal 6. Bottom horizon...
- 4-side moulder - FUTURA KRONO S 220x160 year of manufacturing 1994 bench lenght 2000 mm working width from 25 to 220 mm working height from 8 to 160 mm No. 4 spindle diameter 40 mm (too...1994
- 5+1 spindles moulder RMM623U Working width (cutter OD110mm) 20-230 Working thickness (cutter OD110mm) 8-160 Spindle QTY 5+1 - Dia of shaft (mm) Ø40 Spindle rotation speed(r/min) 1st bot...
- Cod: (008276) Position 1: Planers/Moulding Machines KENTWOOD-FEEDMAC31+M200+FEEDMAC33 Position 2: Panel Feeding and Loading KENTWOOD-FEEDMAC31+M200+FEEDMAC33 Position 3: Panel Stac...
- Gubish 6-Axis Moulding Machine Gubish second hand 106340
Pagini
Pe această pagină sunt listate maşini rindeluit 4 feţe de vânzare pe site-ul nostru. Puteti gasi maşini rindeluit 4 feţe noi si second hand cu 4,5,6,7,8,9,10 axe, universale, automate si semiautomate.